Ricoh SH-P1 M020 Field Service Manual Download Page 234 | Manualshive

Page: 234 / 312

background image

Example: G1772700016.nv,

11. Exit the SP mode.
12. Turn off the main power switch.
13. Remove the SD card.
14. Mark the SD card with the machine code for later reference. You will need this SD card to

download NVRAM to the new NVRAM.

• One SD card can store the NVRAM data of two or more machines.

Downloading NVRAM Data

Follow this procedure to download the data from the SD card to the NVRAM, after the NVRAM has
been replaced.

• If the NVRAM data file cannot be downloaded successfully, the settings must be restored manually

using the SMC report that was printed before NVRAM uploading.

1. Confirm that the main power switch is off.
2. Confirm that you have the SD card that contains the proper NVRAM data for the machine.

3. Remove the SD card slot cover [A] ( x 1 [B]).
4. Insert the SD card into Slot 2 [D] (Lower).
5. Turn on the main power switch.
6. Enter the SP mode and do SP5825 (NVRAM Download).
7. Push [#Enter].

5. System Maintenance Reference

232

5

«
...
232
233
234
235
236
...
»

Summary of Contents for SH-P1 M020

























































































































































































































































































































Reviews:

No comments

Related manuals for SH-P1 M020

Brand: Ier Pages: 8

Brand: DataCard Pages: 25

Brand: Glunz & Jensen Pages: 104

Brand: Oki Pages: 2

Brand: iDPRT Pages: 74

Brand: Memjet Pages: 181

Brand: FELIXrobotics Pages: 65

ECOSYS P5021cdw

Brand: Kyocera Pages: 31

Brand: Lanier Pages: 4

ID MAKER Zenius

Brand: IDVille Pages: 66

ApeosPort-IV C5580

Brand: Fuji Xerox Pages: 739

Brand: Lexmark Pages: 2

SLK-TE20 Series

Brand: SEWOO Pages: 31

imagePROGRAF PRO-6600

Brand: Canon Pages: 939

Brand: Oki Pages: 69

d-Copia 1801MF Plus

Brand: Olivetti Pages: 492

Brand: Oki Pages: 1087

Brand: Riso Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands