Ricoh Pro 1106EX Operating Instructions Manual Download Page 63

Page: 63 / 234

Copying from the Multi Bypass Tray

Copying from the Multi Bypass Tray

The multi bypass tray allows you to copy non-standard paper.

Important

❒

Following paper sizes can be copied from the multi bypass tray:
• When using the Large Capacity Tray (LCT)

Vertical: 100-305.0 mm (3.9"-12"), Horizontal: 140-458 mm (5.5"-18")

• When using the Wide Large Capacity Tray (Wide LCT)

Vertical: 100-330.2 mm (3.9"-13"), Horizontal: 140-458 mm (5.5"-18")

❒

The machine can detect the following sizes as regular size copy paper:
A3

, B4 JIS

, A4

, B5 JIS

, A5

, A6

, 11"

17"

, 8

11"

13"

, 5

,12"

18"

. If you want to use the size of paper

other than the above, be sure to specify the size.

❒

The maximum number of sheets you can load into the multi bypass tray de-
pends on paper type. The number should not exceed the upper limit.

Set the side fences to the paper size.

Place paper in the multi bypass tray (Tray 7).

Adjust the side fences again to ensure they properly fit the paper size.

Set the end fence.

To remove the end fence, slide it to the right by pressing the stopper down.

APF028S

APF029S

Summary of Contents for Pro 1106EX











































































































































































































































Search results

Summary of Contents for Pro 1106EX

Reviews:

Related manuals for Pro 1106EX

Brands by name

Popular brands

Ricoh Pro 1106EX, Operating Instructions Manual

Search results

Summary of Contents for Pro 1106EX

Reviews:

Related manuals for Pro 1106EX

Brands by name

Popular brands