manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 314 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 314

The download is finished when the message prompts you to close.

3. Press the “Exit” button. Then turn the copier off and on again.

NVRAM Data Upload/Download

Uploading Content of NVRAM to an SD card

Do the following procedure to upload SP code settings from NVRAM to an SD card.

• This data should always be uploaded to an SD card before the NVRAM is replaced.
• Make sure that the write protection of an SD card is unlocked

1. Do SP5990-001 (SMC Print) before you switch the machine off. You will need a record of the NVRAM

settings if the upload fails.

2. Switch the copier main power switch off.
3. Remove the SD slot cover (

 x 1).

4. Insert the SD card into SD card slot 3. Then switch the copier on.
5. Execute SP5824-001 (NVRAM Data Upload) and then press the “Execute” key.
6. The following files are coped to an NVRAM folder on the SD card when the upload procedure is

finished. The file is saved to the path and the following filename:
NVRAM\<serial number>.NV
Here is an example with Serial Number “K5000017114”:

5. System Maintenance Reference

312

5

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments