manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 25 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 25

2. Installation

Installation Requirements

Environment

1. Temperature Range: 10°C to 32°C (50°F to 89.6°F)
2. Humidity Range: 15% to 80% RH
3. Ambient Illumination: Less than 1500 lux (do not expose to direct sunlight)
4. Ventilation: 3 times/hr/person or more
5. Do not let the machine get exposed to the following:

1) Cool air from an air conditioner
2) Heat from a heater

6. Do not install the machine in areas that are exposed to corrosive gas.
7. Install the machine at locations lower than 2,500 m (8,200 ft.) above sea level.
8. Install the machine on a strong, level base. (Inclination on any side must be no more than 5 mm.)
9. Do not install the machine in areas that get strong vibrations.

23

2

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments