Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 24 | Manualshive

Page: 24 / 856

Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 24

Guidance for Those Who are Familiar with

Predecessor Products

Machine D023/D025 is a successor model to Machine B230/B237. If you have experience with the
predecessor products, the following information will be of help when you read this manual.
Different Points from Predecessor Products

D023/D025

B230/B237

Basic PM Interval

120K prints

80K prints

PM Operation for PCU

New steps were added to the
replacement procedure for the drum
unit

• Turn the development roller

counterclockwise.

• Do SP 1902-001.

-

PCU Drive Mechanism

Drum/development drive motor
and development clutch for each
color
(AP type)

K: Drum/development drive motor
and development clutch
CMY: Drum drive motor and
development drive motor for all
colors

Duplex Mechanism

Paper is inverted inside the unit (AP
type).

Paper is inverted using the inverter
tray of the mainframe.

SD Card Slots

2 slots

3 slots

Location of Firmware for
Printer, Scanner, Netfile,
NIB, WebDocBox,
WebSys, and DESS

Flash ROM on the controller board Printer/scanner SD card

1. Product Information

22

1

«
...
22
23
24
25
26
...
»

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments