manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 64 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 64

Bit Switches

• Do not adjust a bit switch or use a setting that is described as "Not used", as this may cause the

machine to malfunction or to operate in a manner that is not accepted by local regulations. Such
bits are for use only in other areas, such as Japan.

Default settings for bit switches are not listed in this manual. Refer to the System Parameter List printed by
the machine.

System Switches

System Switch 00 (SP No. 1-101-001)

No

Function

Comments

0

Dedicated transmission parameter
programming
0: Disabled
1: Enabled

Set this bit to 1 before changing any dedicated
transmission parameters.
This setting is automatically reset to "0" after turning
off and on.

1

Not used

Do not change

2

Technical data printout on the
Journal
0: Disabled
1: Enabled

1: Instead of the personal name, the following data
are listed on the Journal for each G3 communication.

4. Service Tables

62

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments