Ricoh LP124w Software Manual Download | Manualshive

Page: 359 / 376

background image

Cautions to Take When Using in a network

345

11

Configuring the WINS Server

The printer can be configured to register its NetBIOS name with a WINS server
when the power is turned on. This enables the NetBIOS name of the printer to
be specified from SmartDeviceMonitor for Admin even in a DHCP environ-
ment. This section explains configuring the WINS server.

Note

❒

The WINS server is supported with Windows NT 4.0 Server Service Pack 4 or
higher, and Windows 2000 Servers WINS Manager.

❒

For details about the WINS server settings, see Windows Help.

❒

If there is no reply from the WINS server, the NetBIOS name is registered by
broadcast.

❒

The NetBIOS name can be entered using up to 13 alphanumeric characters.

Using Web Image Monitor

A

Start a Web browser.

B

Enter “http://(printer’s address)/” in the address bar to access the printer
whose settings you want to change.

Top Page of Web Image Monitor appears.

C

Click

[

Login

]

.

The dialog box for entering the user name and password appears.

D

Enter the user name and password, and then click

[

Login

]

.

Contact your administrator for information about the settings.

E

In the left area, click

[

Configuration

]

, and then click

[

Network

]

.

F

Click

[

TCP/IP

]

.

G

Check that

[

Enable

]

is selected for

[

WINS

]

in the

[

EIEEE 802.11b column

]

,

and then enter the WINS server IPv4 address in

[

Primary WINS Server

]

and

[

Secondary WINS Server

]

.

H

Click

[

OK

]

.

I

Quit Web Image Monitor.

Using telnet

See p.217 “Remote Maintenance by telnet”.

«
...
357
358
359
360
361
...
»

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Related manuals for LP124w

imagePROGRAF iPF8400

Brand: Canon Pages: 157

Brand: Canon Pages: 91

Brand: Pantum Pages: 94

WorkCentre Pro 421

Brand: Xerox Pages: 4

WorkCentre Pro 412

Brand: Xerox Pages: 212

WORKCENTRE PE 220

Brand: Xerox Pages: 8

WORKCENTRE PE 220

Brand: Xerox Pages: 2

WORKCENTRE PE 220

Brand: Xerox Pages: 200

WorkCentre m940

Brand: Xerox Pages: 86

Brand: Xerox Pages: 24

WorkCentre PE16

Brand: Xerox Pages: 201

WorkCentre M24 Color

Brand: Xerox Pages: 441

WORKCENTRE C2424

Brand: Xerox Pages: 2

WorkCentre M118

Brand: Xerox Pages: 5

WORKCENTRE C2424

Brand: Xerox Pages: 16

WORKCENTRE C2424

Brand: Xerox Pages: 20

WORKCENTRE C2424

Brand: Xerox Pages: 25

2006NPC - DocuColor Color Laser

Brand: Xerox Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands