Ricoh LP124w Software Manual Download | Manualshive

Page: 338 / 376

background image

Mac OS Configuration

324

9

Printer Utility for Mac Functions

Downloading PS Fonts

You can download the PS fonts to the printer memory or hard disk drive.

Important

❒

The following procedure to download the fonts assume that you are a system
administrator. If you are not, be sure to consult your system administrator.

❒

During the download, do not turn off the power switch, operate the panel or
open or close the cover.

❒

If the printer restarts, all the printer settings return to the defaults.

❒

Confirm that a Macintosh and the printer are connected with Appletalk.

A

Select

[

Download PS Fonts...

]

on the

[

File

]

menu.

B

Click

[

Add to list

]

.

The dialog box to select fonts appears.

C

Select the desired font files, and then click

[

Open

]

.

The list of selectable font names appears.

D

After adding all the fonts you want to download, click

[

OK

]

.

The dialog box of selected fonts to download appears.

E

Click

[

Download

]

.

The fonts begin to download, and the download status is shown.

F

When the completion message appears, click

[

OK

]

.

G

Click

[

Cancel

]

.

Note

❒

Some fonts cannot be downloaded.

❒

Before downloading, read the documentation about the fonts you want to
use.

«
...
336
337
338
339
340
...
»

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Related manuals for LP124w

Brand: EBS Pages: 34

Brand: Oki Pages: 2

OKIPAGE 8c Plus

Brand: Oki Pages: 48

Brand: Oki Pages: 257

Brand: Oki Pages: 113

Brand: Oki Pages: 26

Brand: Oki Pages: 183

Brand: Oki Pages: 36

Brand: Oki Pages: 136

Brand: Oki Pages: 66

Brand: Oki Pages: 123

Brand: Oki Pages: 109

Brand: Oki Pages: 68

Brand: Oki Pages: 12

Brand: Oki Pages: 22

Brand: Oki Pages: 22

Brand: Oki Pages: 27

OKIPAGE 12i Series

Brand: Oki Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands