manualshive.com logo in svg

Ricoh LP124w, Software Manual

Share
Download
Ricoh LP124w Software Manual Download Page 305

291

8. Special Operations under

Windows

Printing Files Directly from Windows

You can print files directly using Windows commands. For example, you can
print PostScript files for PostScript 3.

❖

Windows 95/98/Me

You can print files directly using “ftp” command.

❖

Windows 2000/XP, Windows Server 2003/2003 R2, Windows NT 4.0

You can print files directly using “lpr”, “rcp”, or “ftp” command.

Note

❒

To use “sftp” commands, use an sftp client software that is compatible with
ssh v2.

Setup

Follow the procedure below to make network environment settings.

A

Enable TCP/IP with the control panel, and then set up the printer’s network
environment about TCP/IP including IP addresses.

TCP/IP of the printer is set as default.

B

Install a TCP/IP in Windows to set up the network environment.

Consult the administrator for the local setting information.

C

To print under Windows 2000/XP, Windows Server 2003/2003 R2, or Win-
dows NT 4.0, install “Printing service for UNIX” as the network applica-
tion. To print under Windows NT 4.0, install “Microsoft TCP/IP printing”
as the network application.

Reference

For details about setting up “IPv4 address”, see Hardware Guide.
For details about setting the “IPv4 address” of the printer using DHCP, see
p.342 “Cautions to Take When Using in a network”.

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands