Ricoh LP124w Page 261 Software Manual Download

Page: 261 / 376

Remote Maintenance by telnet

247

status

Use the “status” command to display the printer status.

❖

Messages

msh> status

Reference

p.254 “Getting Printer Information over the Network”.

syslog

Use the “syslog” command to display the information stored in the printer’s sys-
tem log.

❖

View message

msh> syslog

Reference

p.267 “Message List”.

upnp

Use the “upnp” command to display and configure the universal plug and play.

❖

Public URL display

msh> upnp url

❖

Public URL configuration

Msh< upnp url "string"

• Enter the URL string in the character string.

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands