Ricoh LP124w Software Manual Download

Page: 249 / 376

Remote Maintenance by telnet

235

route

Use the “route” command to view and control the routing table.

❖

All route information display

msh> route get "destination"

• Specify the IPv4 address to destination.

“0.0.0.0” cannot be specified as destination address.

• If you do not specify a destination address, all the information about the

router is displayed.

❖

Enabling/disabling Specified IPv4 Destination

msh> route active {host|net} "destination" {on | off}

• You can turn the specified destination on or off. Host becomes the default

setting.

❖

Adding IPv4 Routing Table

msh> route add {host|net} "destination" "gateway"

• Adds a host or network route to “destination”, and a gateway address to

“gateway” in the table.

• Specify the IPv4 address to destination and gateway.
• Host becomes the default setting.

❖

Setting Default IPv4 Gateway

msh> route add default gateway

❖

Deleting specified IPv4 destination from Routing Table

msh> route delete {host|net} "destination"

• Host becomes the default setting.
• IPv4 address of destination can be specified.

❖

Setting IPv6 Default Gateway

msh> route add6 default "gateway"

❖

Adding a specified IPv6 destination to Routing Table

msh> route add6 "destination" "prefixlen" "gateway"

• Specify the IPv6 address to destination and gateway.

❖

Deleting a specified IPv6 destination from Routing Table

msh> route delete6 "destination" "prefixlen"

• Specify the IPv6 address to destination and gateway.

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands