manualshive.com logo in svg

Ricoh LP124w, Software Manual

The Ricoh LP124w Hardware Manual is the essential guide for users of this cutting-edge printer. Accessible, comprehensive, and free to download from our website, this manual provides step-by-step instructions and troubleshooting tips to optimize the performance of your device. Master your printer with ease and enhance your printing experience with the Ricoh LP124w Hardware Manual. Download now at manualshive.com.

Share
Download
background image

Remote Maintenance by telnet

227

6

hostname

Use the “hostname” command to change the printer name.

❖

View settings

msh> hostname

❖

IPv4 Configuration

msh> hostname "interface_name" "printer_name"

• Enter the printer name using up to 63 alphanumeric characters.
• You cannot use a printer name starting with “RNP” or “rnp”
• The Ethernet interface and IEEE 802.11b interface will have the same print-

er name.

• wlan can be specified only when the IEEE 802.11b interface unit is in-

stalled.

❖

Initializing the printer name for each interface

msh>hostname "interface_name" clear "name"

Interface name

Interface configured

ether

Ethernet interface

wlan

IEEE 802.11b interface

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Related manuals for LP124w

Canon CX-G2400 Basic Operation Manual preview
CX-G2400
Brand: Canon Pages: 58
Canon image Prograf iPF680 Series Basic Manual preview
image Prograf iPF680 Series
Brand: Canon Pages: 132
Canon i470D Series Printing Manual preview
i470D Series
Brand: Canon Pages: 44
Canon imageClass LBP6230dw Getting Started preview
imageClass LBP6230dw
Brand: Canon Pages: 16
Canon i960 Series Printing Manual preview
i960 Series
Brand: Canon Pages: 2
Canon imageprograf IPF785 Service Manual preview
imageprograf IPF785
Brand: Canon Pages: 42
Canon CX 320 User Manual preview
CX 320
Brand: Canon Pages: 148
Canon Color Bubble Jet BJC-8200 Quick Start Manual preview
Color Bubble Jet BJC-8200
Brand: Canon Pages: 6
Canon Color Bubble Jet BJC-1000 Series Specification preview
Color Bubble Jet BJC-1000 Series
Brand: Canon Pages: 2
Canon BJC-S530D Start Here preview
BJC-S530D
Brand: Canon Pages: 2
Canon BJC-S520 Setup Instructions preview
BJC-S520
Brand: Canon Pages: 2
Canon Color Bubble Jet BJC-8200 Service Manual preview
Color Bubble Jet BJC-8200
Brand: Canon Pages: 105
Canon i9900 Series Start Here preview
i9900 Series
Brand: Canon Pages: 2
Canon i900D Series Quick Start Manual preview
i900D Series
Brand: Canon Pages: 68
Canon i900D Series Printing Manual preview
i900D Series
Brand: Canon Pages: 4
Canon i900D Series Setup Instructions preview
i900D Series
Brand: Canon Pages: 2
Canon i80 Series Setup Instructions preview
i80 Series
Brand: Canon Pages: 2
Canon i70 Series Start Here preview
i70 Series
Brand: Canon Pages: 2

Brands by name

Popular brands

Load more brands