manualshive.com logo in svg

Ricoh LP124w, Software Manual

Share
Download
Ricoh LP124w Software Manual Download Page 235

Remote Maintenance by telnet

221

6

❖

Interface configuration

msh> bonjour linklocal "interface_name"

• If many types of interface are installed, configure the interface that com-

municates with linklocal address.

• If the connected computer's IP address is a link local address specified by

the DHCP's Autonet, and multiple interfaces are connected to the printer,
you can select an interface to communicate through.

• If you do not specify an interface, the Ethernet interface is automatically se-

lected.

• wlan can be specified only when the IEEE 802.11b interface unit is in-

stalled.

❖

Selecting the IPP port number

msh> bonjour ippport {ipp | ssl}

• Appears when SSL is enabled.
• If the “ipp” is selected, the port number is set to “631”. If the “ssl” is select-

ed, the port number is set to “443”.

devicename

Use the “devicename” command to display and change the printer name.

❖

View settings

msh> devicename

❖

Printer name configuration

msh> devicename name "string"

• Enter a printer name using up to 31 alphanumeric characters.
• Set single names for each printer.

❖

Printer name initialization

msh> device name clearname

• Reset the printer name to its default.

Interface name

Interface configured

ether

Ethernet interface

wlan

IEEE 802.11b interface

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands