Ricoh LP124w Page 234 Software Manual Download

Page: 234 / 376

Monitoring and Configuring the Printer

220

bonjour (rendezvous)

Use the “bonjour (rendezvous)” command to display bonjour (rendezvous)-re-
lated settings.

❖

View settings

Bonjour settings are displayed.

msh> bonjour

❖

Bonjour service name setting

You can specify the bonjour service name.

msh> bonjour cname "computer name"

• The computer name can be entered using up to 63 alphanumeric characters.

❖

Bonjour Installation location information setting

You can enter information about the location where the printer is installed.

msh> bonjour location "location"

• Information about location can be entered using up to 32 alphanumeric

characters.

❖

Setting order of priority for each protocol

• diprint

msh> bonjour diprint

[

0-99

]

• lpr

msh> bonjour lpr

[

0-99

]

• ipp

msh> bonjour ipp

[

0-99

]

You can specify the order of priority for “diprint”, “lpr”, and “ipp”. Smaller
numbers indicate higher priority.

❖

IP TTL setting

msh> bonjour ip ttl {1-255}

You can specify the IP TTL (the number of routers a packet can pass through).

Note

❒

The default is 255.

❖

Resetting the computer name and location information

You can reset the computer name and location information.

msh> bonjour clear {cname | location}

• cname

Reset the computer name. The default computer name will be displayed
when the computer is restarted.

• location

Reset the location information. The previous location information will be
deleted.

Summary of Contents for LP124w
























































































































































































































































































































































































Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands

Ricoh LP124w, Software Manual

Search results

Summary of Contents for LP124w

Reviews:

Related manuals for LP124w

Brands by name

Popular brands