Ricoh Aficio MP 2500 Facsimile Reference Manual Download | Manualshive

Page: 167 / 204

background image

157

5. Fax via Computer

This section explains how to use this machine's facsimile function from a com-
puter via a network.

Sending Fax Documents from Computers

You can send a document created with a Windows application from a computer
connected to the machine to another fax machine.
Connect computers to the machine via parallel port, LAN, IEEE 802.11b (wire-
less LAN), or USB 2.0.
• To send a fax, simply select

[

Print...

]

from the Windows application, then select

LAN-Fax as the printer, and then specify a destination. LAN-Fax enables pa-
perless faxing from your computer to the other destinations.

• In addition to sending faxes, the LAN-Fax Driver allows this machine to be

used for printing out documents prepared on a computer for proof checking.

• To use the LAN-Fax Driver, connect this machine to computers and make the

necessary network settings, and then install the LAN-Fax Driver and the related
utilities on your computer.

ALT007S

«
...
165
166
167
168
169
...
»

Summary of Contents for Aficio MP 2500













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 2500

Brand: Panasonic Pages: 83

Brand: Oki Pages: 17

Brand: Oki Pages: 12

Brand: Oki Pages: 30

Brand: Oki Pages: 391

Brand: Oki Pages: 2

Brand: EBS Pages: 34

Brand: Xerox Pages: 414

Brand: Aficio Pages: 188

Color Jetprinter 810 Series

Brand: Lexmark Pages: 2

Brand: Pantum Pages: 111

Brand: Xerox Pages: 233

Brand: Delta OHM Pages: 28

Brand: Konica Minolta Pages: 285

Brand: Avery Weigh-Tronix Pages: 40

Brand: Xante Pages: 106

Brand: SNBC Pages: 52

Brand: Epson Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands