Ricoh Aficio MP 2000L Scanner Reference Download Page 110

Page: 110 / 134

Various Scan Settings

104

File Type

This section explains the procedure for selecting a file type.

Important

❒

To deliver files, set the file type using the delivery server computer. For de-
tails, see the manuals supplied with the ScanRouter delivery software.

You can select one of the following file types:
• Single Page:TIFF
• Single Page:PDF
• Multi-page:TIFF
• Multi-page:PDF

Press

[

Options

]

Press the

{U}

{T}

key to select

[

File Type

]

, and then press the

{

}

key.

Press the

{U}

{T}

key to select the file type, and then press the

{

}

key.

"Programmed" appears, and then the Send Options screen appears.

Press the

{

Escape

}

key.

Summary of Contents for Aficio MP 2000L







































































































































Search results

Summary of Contents for Aficio MP 2000L

Reviews:

Related manuals for Aficio MP 2000L

Brands by name

Popular brands

Ricoh Aficio MP 2000L, Scanner Reference

Search results

Summary of Contents for Aficio MP 2000L

Reviews:

Related manuals for Aficio MP 2000L

Brands by name

Popular brands