Ricoh Aficio MP 161SPF Troubleshooting Manual Download Page 45 | Manualshive

Page: 45 / 100

background image

When a Message Is Displayed

39

4

When a Message Is Displayed

This section describes the principal messages that appear on the display panel.
If a message not described here appears, act according to the message.

Reference

Before turning the main power off, see “Turning On the Power”, About This
Machine.

Status Messages

This section describes the machine status messages.

Message

Status

Ready

This is the default ready message. The machine is ready
for use. No action is required.

Printing...

The machine is printing. Wait a while.

Waiting...

The machine is waiting for the next data to print. Wait a
while.

Offline

The machine is offline. To start printing, switch the ma-
chine online by pressing the

{

Online

}

Key.

Please wait.

This message may appear for a few seconds. It means the
machine is initializing or executing maintenance opera-
tions. Wait a while.

Resetting Job...

The machine is resetting the print job. Wait until
“

Ready

” appears on the display panel.

Setting change...

The machine settings are being changed. Wait a while.

Hex Dump Mode

In Hex Dump mode, the machine prints received data in
hexadecimal format. Turn off the machine after printing,
and then turn back on. Hex Dump mode is used for ad-
vanced troubleshooting.

«
...
43
44
45
46
47
...
»

Summary of Contents for Aficio MP 161SPF





































































































Reviews:

No comments

Related manuals for Aficio MP 161SPF

Brand: NCR Pages: 10

Brand: Oki Pages: 28

Brand: Oki Pages: 22

image RUNNER 3045

Brand: Canon Pages: 14

Brand: Oki Pages: 512

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

Brand: Muratec Pages: 213

Brand: Telpar Pages: 52

Brand: M&R Pages: 36

Brand: WOOSIM Pages: 20

Brand: WOOSIM Pages: 29

Brand: Oki Pages: 106

Virtuoso SG400EU

Brand: Sawgrass Pages: 135

Magicolor 2300 DL

Brand: Minolta Pages: 72

Brand: SATO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands