Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 288

background image

Connecting the Machine

22

1

Settings Required to Use Scan to Folder Function

This section lists the settings required for sending files.

Ethernet

This section lists the settings required for sending files with an Ethernet connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".

Note

❒

For the Effective Protocol setting, check that the protocol you want to use is
set to

[

Effective

]

.

❒

[

LAN Type

]

is displayed when the wireless LAN interface board is installed. If

both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected in-
terface takes precedence.

Reference

p.47 “Interface Settings”
p.53 “File Transfer”

Menu

User Tool

Setting Requirements

Interface Settings/Network IP Address

Necessary

Interface Settings/Network Gateway Address

Necessary

Interface Settings/Network DNS Configuration

As required

Interface Settings/Network DDNS Configuration

As required

Interface Settings/Network Domain Name

As required

Interface Settings/Network WINS Configuration

As required

Interface Settings/Network Effective Protocol

Necessary

Interface Settings/Network Ethernet Speed

As required

Interface Settings/Network LAN Type

Necessary

Interface Settings/Network NCP Delivery Protocol

As required

Interface Settings/Network Permit SNMPv3 Communication

As required

Interface Settings/Network Permit SSL/TLS Communication

As required

Interface Settings/Network Host Name

As required

File Transfer

Default User Name / Password (Send)

As required

File Transfer

Scanner Recall Interval Time

As required

File Transfer

Number of Scanner Recalls

As required

«
...
28
29
30
31
32
...
»

Summary of Contents for Aficio IS 2425

































































































































































































































































































Reviews:

No comments

Related manuals for Aficio IS 2425

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 52

SuperScript 1800

Brand: NEC Pages: 8

Brand: IBM Pages: 102

Brand: Oki Pages: 48

Brand: Oki Pages: 34

Brand: Oki Pages: 65

Brand: Oki Pages: 44

Brand: Oki Pages: 36

Brand: OHAUS Pages: 28

Brand: Oce Pages: 396

Brand: Oce Pages: 28

Brand: Oki Pages: 64

Brand: QMS Pages: 208

Brand: Olivetti Pages: 24

Compa II Series

Brand: Valentin Pages: 110

Digital Color Press 700

Brand: Xerox Pages: 216

Brand: Citizen Pages: 104

Brand: Olivetti Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands