Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 235

Page: 235 / 288

Registering Folders

227

Using NCP to Connect

This section describes the procedure for registering, changing, and deleting NCP
folders.

Note

❒

To register a shared folder configured in Windows, see “Using SMB to Connect”

❒

To register a folder in an FTP server, see “Using FTP to Connect”

Reference

p.215 “Using SMB to Connect”
p.221 “Using FTP to Connect”

Registering an NCP Folder

This section describes how to register an NCP folder.

Press

[

System Settings

]

Press

[

Administrator Tools

]

Press

[

Next

]

Press

[

Address Book Management

]

Check that

[

Program / Change

]

is selected.

Press the name you want to register or enter the registered number using
the number keys.

If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.

Press

[

Auth. Info

]

, and then press

[

Next

]

Press

[

Specify Other Auth. Info

]

on the right side of Folder Authentication.

When

[

Do not Specify

]

is selected, the NCP User Name and NCP Password that

you have specified in Default User Name / Password (Send) of File Transfer
settings applies. For details, see "File Transfer".

Press

[

Change

]

under Login User Name.

Enter the login user name, and then press

[

]

Press

[

Change

]

under Login Password.

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands