Ricoh Aficio IS 2325 Operating & Troubleshooting Instructions Download Page 46 | Manualshive

Page: 46 / 126

background image

Troubleshooting When Using the Facsimile Function

38

3

When an Error Occurs Using Internet Fax

This section describes reports that the machine sends if an Internet Fax error occurs.

Error Mail Notification

The machine sends the Error Mail Notification to the sender when it is unable to
successfully receive a particular e-mail message. A “cc” of this notification is also
sent to the administrator's e-mail address when one is specified.

Note

❒

You can select to send Error Mail Notification with User Parameters. See “Pa-
rameter Setting”, General Settings Guide.

❒

If Error Mail Notification cannot be sent, the Error Report (E-Mail) is printed
by the machine.

❒

If an error occurs when e-mail is received via SMTP, the SMTP server sends
error e-mail to the originator of the document.

Reference

“Parameter Setting”, General Settings Guide

Error Report (E-Mail)

The Error Report (E-Mail) is printed by the machine when it is unable to send an
Error Mail Notification.

Server-Generated Error E-mail

The transmitting server sends this error e-mail to the originator of e-mail that
cannot be transmitted successfully (due to reasons such as specifying an incor-
rect e-mail address).

Note

❒

After server-generated error e-mail is printed, the first page of the sent docu-
ment is printed.

«
...
44
45
46
47
48
...
»

Summary of Contents for Aficio IS 2325































































































































Reviews:

No comments

Related manuals for Aficio IS 2325

Brand: Datamax Pages: 2

Brand: Lanier Pages: 265

VariQuest Perfecta 2400STP

Brand: Varitronics Pages: 227

Brand: Seiko Pages: 76

Brand: Oki Pages: 20

Brand: TransAct Pages: 45

Brand: Shandong New Beiyang Information Technology Co. Pages: 47

ColourLaser 21 Series

Brand: Xante Pages: 32

4650NX - SuperScript Color Laser Printer

Brand: NEC Pages: 74

WORKCENTRE 7428

Brand: Xerox Pages: 208

Brand: Loadrite Pages: 16

Brand: Mitsubishi Electric Pages: 16

Brand: Mitsubishi Electric Pages: 8

Brand: Mitsubishi Electric Pages: 2

Brand: Mitsubishi Electric Pages: 35

Brand: Mitsubishi Electric Pages: 27

Brand: Mitsubishi Electric Pages: 25

Brand: Mitsubishi Electric Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands