Ricoh Aficio CL5000 Maintenance Manual Download | Manualshive

Page: 73 / 80

background image

Moving and Transporting the Printer

69

4

Moving the Printer

Moving the printer in a short distance

AAAA

Be sure to check the following points:

• The power switch is turned off.
• The power cable is unplugged from the wall outlet.
• The interface cable is unplugged from the printer.

BBBB

If the external options are installed, remove them.

See the Option Setup Guide and follow the steps backwards for removing op-
tions. For removing the Duplex Unit, Finisher and 4-bin Mailbox, follow the
steps below.

A

Removing the Duplex Unit

Remove the two stoppers to release the supporting bar. Hold the unit with both
hands and move it towards the left (

B

) while pressing down the lever (

A

).

B

Removing the Finisher

Open the Bypass Tray and the Duplex Unit. Then open the right covers of
the printer and the Interchange Unit.
Remove the three screws that are fastening the printer and the Finisher.
Press the two levers shown in the illustration to release the lock.

Hold the Finisher with both hands, and then slowly pull it out of the printer.

ZESP310J

ZESP313J

«
...
71
72
73
74
75
...
»

Summary of Contents for Aficio CL5000

















































































Reviews:

No comments

Related manuals for Aficio CL5000

Brand: Panasonic Pages: 155

Brand: Panasonic Pages: 160

Brand: Keeler Pages: 25

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

Brand: Hanin Pages: 27

Brand: Canon Pages: 65

Brand: ICT Pages: 34

Brand: StarTech.com Pages: 13

Brand: Oki Pages: 276

Brand: Brightek Pages: 8

Brand: Lexmark Pages: 79

Brand: Oki Pages: 271

DocumentCentre C240 Series

Brand: Fuji Xerox Pages: 275

Brand: Konica Minolta Pages: 4

Brand: Ricoh Pages: 849

Brand: Kyocera Pages: 44

Brand: Sharp Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands