Ricoh Aficio CL5000 Maintenance Manual Download

Page: 61 / 80

Cleaning the Registration Roller and the Guide Boards

Cleaning the Registration Roller and the
Guide Boards

CAUTION:

AAAA

Turn off the printer power.

BBBB

Open the Bypass Tray.

Note

❒

Remove the paper on the By-
pass Tray to prevent them from
falling.

CCCC

If the Duplex Unit is installed,
open it by pushing the catch up-
wards.

DDDD

Open the right cover of the print-
er by pushing up the handle.

Important

❒

Do not touch the inside of the
printer as it may cause an inju-
ry.

EEEE

Wipe the registration roller with a
well-wrung wet cloth while turn-
ing the roller.

The registration roller is installed
as shown in the illustration.

Important

❒

Do not use alcohol or detergent.

•

The inside of the machine be-
comes very hot. Do not touch the
parts with a label indicating "

(means hot surface). Touching
"

" (means hot surface) could

result in a burn.

ZESH206J

ZESH510J

ZESH458J

ZESH703J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands