Ricoh 161 Function Manual Download Page 89

Page: 89 / 192

Canceling a Transmission

Canceling a Transmission

This section explains how to cancel a fax transmission.

Important

❒

Remember that the Communicating indicator turns off almost immediately
when an Internet Fax is being sent.

Before the Original Is Scanned

Use this procedure to cancel a transmission before pressing the

{

Start

}

key.

Press the

{

Clear Modes

}

key.

Note

❒

When originals are placed into the ARDF, you can cancel transmission
simply by removing them.

While the Original Is Being Scanned

Use this procedure to cancel a transmission after pressing the

{

Start

}

key.

Press the

{

Clear/Stop

}

key.

The machine stops scanning.

Note

❒

Scanning may be completed while you are performing the cancel operation.

ASO034S

ASO035S

Summary of Contents for 161

































































































































































































Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands

Ricoh 161, Function Manual

Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands