Ricoh 161 Function Manual Download Page 155 | Manualshive

Page: 155 / 192

background image

147

5. Fax via Computer

This section explains how to use this machine's facsimile function from a com-
puter via a network.

Sending Fax Documents from Computers

You can send a document created with a Windows application from a computer
connected to the machine to another fax machine.
Connect computers to the machine via parallel port, LAN, IEEE 802.11b (wire-
less LAN), or USB 2.0.
• To send a fax, simply select

[

Print...

]

from the Windows application, then select

LAN-Fax as the printer, and then specify a destination. LAN-Fax enables pa-
perless faxing from your computer to the other destinations.

• In addition to sending faxes, the LAN-Fax Driver allows this machine to be

used for printing out documents prepared on a computer for proof checking.

• To use the LAN-Fax Driver, connect this machine to a LAN and make the nec-

essary network settings, and then install the LAN-Fax Driver and the related
utilities on your computer.

ALT007S

«
...
153
154
155
156
157
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

Brand: SA Pages: 5

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands