Ricoh 161 Function Manual Download Page 132 | Manualshive

Page: 132 / 192

background image

Reception

124

3

Center Mark

When this function is enabled, marks are printed halfway down the left side and
at the top center of each page received.
This makes it easy for you to position a hole puncher correctly when you file re-
ceived documents.

Note

❒

You can enable or disable this function using Center Mark in the Fax Features
menu.

❒

The Center Mark may deviate a little from the exact center of the edge.

Reference

“Fax Features”, General Settings Guide

Reception Time

You can have the date, time, and file number printed at the bottom of the docu-
ment when it is received.

Note

❒

You can turn this function on or off using Print Reception Time in the Fax Fea-
tures menu.

❒

When a received document is split and printed on two or more sheets, the re-
ception time is printed on the last sheet.

❒

The time when the document was printed can also be recorded on the docu-
ment. If you need this function, contact your service representative.

Reference

“Fax Features”, General Settings Guide

«
...
130
131
132
133
134
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

image Prograf iPF785 Series

Brand: Canon Pages: 136

Brand: GBC Pages: 110

WorkCentre Pro 421

Brand: Xerox Pages: 4

WorkCentre Pro 412

Brand: Xerox Pages: 212

WORKCENTRE PE 220

Brand: Xerox Pages: 8

WORKCENTRE PE 220

Brand: Xerox Pages: 2

WORKCENTRE PE 220

Brand: Xerox Pages: 200

WorkCentre m940

Brand: Xerox Pages: 86

Brand: Xerox Pages: 24

WorkCentre PE16

Brand: Xerox Pages: 201

WorkCentre M24 Color

Brand: Xerox Pages: 441

WORKCENTRE C2424

Brand: Xerox Pages: 2

WorkCentre M118

Brand: Xerox Pages: 5

WORKCENTRE C2424

Brand: Xerox Pages: 16

WORKCENTRE C2424

Brand: Xerox Pages: 20

WORKCENTRE C2424

Brand: Xerox Pages: 25

2006NPC - DocuColor Color Laser

Brand: Xerox Pages: 4

WorkCentre XK50cx

Brand: Xerox Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands