Ricoh 161 Function Manual Download Page 131

Page: 131 / 192

Printing Options

123

Printing Options

This section explains useful functions for printing received documents.

Print Completion Beep

When this function is turned on, the machine beeps to let you know when a re-
ceived document is printed.

Note

❒

You can alter the volume of the beep or turn it off completely (set the volume
to the minimum level) using Adjust Sound Volume in the Fax Features menu.

Reference

“Troubleshooting When Using the Facsimile Function”, Troubleshooting

Checkered Mark

When this function is turned on, a Checkered Mark is printed on the first page
of fax documents to help you separate them.

Note

❒

You can turn this function on or off using Checkered Mark in the Fax Features
menu.

Reference

“Fax Features”, General Settings Guide

Summary of Contents for 161

































































































































































































Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands

Ricoh 161, Function Manual

Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands