EDP Commands
© Rice Lake Weighing Systems
●
All Rights Reserved
47
7.5 EDP Setting Commands
CPU Ports
• Ports 1 and 2 are the two RS-232 ports
• Port 3 is the RS-485/422 port
• Port 4 is the USB device port
• Port 5 is the Ethernet port
For ports 4 (USB) and 5 (Ethernet), the only applicable parameters are INPUT, TERMIN, ECHO, RESPONSE, EOLDLY.
All other parameters are ignored.
SC.SEC.ENABLED#
n
Enable the Secondary Units
ON
(default), OFF
SC.FILTERCHAIN#
n
Defines what filter to use
AVGONLY
(default), ADPONLY, DMPONLY, RAW
SC.DAMPINGVALUE#
n
Sets the damping time constant
0–2560 (in 0.1 second intervals),
0
(default)
SC.ADTHRESHOLD#
n
Adaptive filter weight threshold value
0–2000 (in display divisions),
10
(default)
SC.ADSENSITIVITY#
n
Adaptive filter sensitivity
LIGHT
(default), MEDIUM, HEAVY
SC.ACCUM#
n
Accumulator enable
OFF
(default), ON
SC.WZERO#
n
Perform zero calibration
—
SC.TEMPZERO
#n
Perform temporary zero calibration
—
SC.LASTZERO
#n
Perform last zero calibration
—
SC.WVAL#
n
Test weight value
0.000001–9999999.999999,
10000.0
(default)
SC.WSPAN#
n
Perform span calibration
—
SC.WLIN.F1#
n
–
SC.WLIN.F4#
n
Actual raw count value for linearization points 1–4
0–16777215,
0
(default)
SC.WLIN.V1#
n
–
SC.WLIN.V4#
n
Test weight value for linearization points 1–4 (A setting
of 0 indicates the linearization point is not used)
0.000001–9999999.999999,
0.0
(default)
SC.WLIN.C1#
n
–
SC.WLIN.C4#
n
Perform linearization calibration on points 1–4
—
SC.LC.CD#
n
Deadload coefficient raw count value
0–16777215,
8386509
(default)
SC.LC.CW#
n
Span coefficient raw count value
0–16777215,
2186044
(default)
SC.LC.CZ#
n
Temporary zero raw count value
0–16777215,
2186044
(default)
SC.REZERO#
n
Perform the Rezero calibration function
—
SC.INITIALZERO#
n
Initial Zero range in % of full scale
0.0–100.0,
0.0
(default)
SC.RTZGRAD#
n
Number of graduations from the zero base at which
the accumulator re-arms itself
0.0–100.0,
0.4
(default)
Command
Description
Values
EDP.INPUT#
p
Port serial input function
CMD
(default), STRIND, STRLFT, REMOTE
EDP.BAUD#
p
Port baud rate
1200, 2400, 4800,
9600
(default), 19200, 38400, 57600, 115200
EDP.BITS#
p
Port data bits/parity
8NONE
(default), 7EVEN, 7ODD
EDP.TERMIN#
p
Port line termination character
CR/LF
(default), CR
EDP.STOPBITS#
p
Port stop bits
1
(default), 2
EDP.ECHO#
p
Port echo
ON
(default), OFF
EDP.RESPONSE#
p
Port response
ON
(default), OFF
EDP.EOLDLY#
p
Port end-of-line delay
0–255 (0.1-second intervals),
0
(default)
EDP.HANDSHK#
p
Port handshake
OFF
(default), XONXOFF, HRDWAR
EDP.ADDRESS#
p
Port RS-485 address
0–255,
0
(default)
For commands ending with
#p
, p is the port number (1-5)
Table 7-5. Serial Port Commands
Command
Description
Values
For commands ending with
#n
, n is the scale number (1)
Table 7-4. Scales Commands (Continued)
