Rice Lake ELS Series Installation Manual Download Page 9 | Manualshive

Page: 9 / 30

background image

Introduction

©

Rice Lake Weighing Systems

●

All Rights Reserved

5

1.5 Grounding Straps

The grounding straps connected to the ELS weigh stands are used to ground the conveyor to the floor. If the system is not

properly grounded, static can build up and cause damage to the load cells once the static discharges. The grounding straps

protect the load cells by providing an alternate path for the static discharge to travel.
The grounding straps are located on each load cell assembly and connect the load cell top plate to the mounting plate.

Figure 1-2. Grounding Straps

The grounding straps must be connected to the weigh stands at all times.

Grounding Strap

IMPORTANT

«
...
7
8
9
10
11
...
»

Summary of Contents for ELS Series































Reviews:

No comments

Related manuals for ELS Series

Brand: New Star Computer Products Pages: 2

Brand: LA VAGUE Pages: 38

Charger Wall Mount

Brand: minniemobile Pages: 4

Brand: B-Tech Pages: 20

Wall/Ceiling Mounting Bracket MB3

Brand: Electro-Voice Pages: 4

Brand: Elipson Pages: 4

integrator racks

Brand: AUSTRALIAN MONITOR Pages: 12

Brand: PEERLESS Pages: 16

Brand: Tennsco Pages: 4

Brand: PASCO Pages: 3

Brand: Konig & Meyer Pages: 4

Brand: VISIONARY DESIGNS Pages: 2

Brand: HP Pages: 20

11000 G2 series

Brand: HP Pages: 18

Brand: HP Pages: 41

Location Discovery Services

Brand: HP Pages: 8

AlphaServer DS15

Brand: HP Pages: 2

Brand: HP Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands