Rice Lake ELS Series Installation Manual Download Page 26 | Manualshive

Page: 26 / 30

background image

Elevated Load Cell Stands

22

Visit our website

www.RiceLake.com

3.2 Load Cell Replacement

Replacement load cells can be ordered from Rice Lake Weighing Systems, please refer to the replacement parts section. See

Section 2.13 on page 18

1. Brace the conveyor using proper equipment.
2. Loosen the load cell cable mounting clips.
3. Open the junction box and disconnect defective load cell cable.
4. Remove the load cell guard plate.
5. Remove the four 5/16-18 x 3/4 inch bolts that connect the bearing block to the conveyor mounting plate.

Figure 3-2. Conveyor Mounting Plate Removal

6. Remove the two 1/2-20 x 2-1/2 inch bolts that connect the load cell, load cell spacer and the load cell mount plate.

Figure 3-3. Load Cell Removal

7. Remove the load cell and the bearing block.

Bearing Block

Conveyor Mounting

Plate

Conveyor

Load Cell Spacer

Load Cell

«
...
24
25
26
27
28
...
»

Summary of Contents for ELS Series































Reviews:

No comments

Related manuals for ELS Series

Brand: B-Tech Pages: 12

Brand: B-Tech Pages: 12

Brand: Vantage Hearth Pages: 2

Brand: Racking Solutions Pages: 2

Brand: Deltaco Pages: 12

Brand: M-system Pages: 2

Brand: Rehabmart Pages: 3

Brand: iTOOLco Pages: 15

Tip & Touch 062.7650

Brand: Smart Metals Pages: 16

Brand: Toa Pages: 4

Brand: TYAN Pages: 180

Brand: Konig & Meyer Pages: 4

Brand: Konig & Meyer Pages: 2

Brand: Mo-vis Pages: 14

Brand: Craftsman Pages: 4

Brand: Craftsman Pages: 24

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands