23
23
G
B
POINT B
- sETTINGs
DIP 1
(ON) MOTOr rOTATION DIrECTION CHECK (see
Point C
)
DIP 2
(ON)
PrOGrAMMING (see Point D)
DIP 1-2
STORAGE/DELETION OF RADIO CODES FOR
COMPLETE OPENING (DIP 1 ON followed by DIP 2 ON)
(POINT G) ONLY FOR CRX MODELS
DIP 1-3
STORAGE/DELETION OF RADIO CODES FOR PEDESTRIAN
OPENING (DIP 1 ON followed by DIP 3 ON) (POINT H) ONLY FOR
CRX MODELS
DIP 2-1 PrOGrAMMING Of THE PEDEsTrIAN OPENING (see Point f)
DIP 3
ON - Automatic Closing ENABLED
OFF - Automatic Closing DISABLED
DIP 4
ON - Photocells active only in closing
OFF - Photocells always active
DIP 5
ON - blinker pre-flashing
OFF - blinker normal-flashing
DIP 6
OFF - STEP BY STEP
Single pulse contact (K BUTT)
Pedestrian button (PED BUTT)
Radio Receiver command
ON - AUTOMATIC
Single pulse contact (K BUTT)
Pedestrian button (PED BUTT)
Radio Receiver command
DIP 7
ON - low speed in approaching ENABLED
OFF - low speed in approaching DISABLED
DIP 8
ON - electric lock command ENABLED
OFF - electric lock command DISABLED
DIP 9
ON - Hammering on complete close position to ease Manual Release
- Hammering before opening to ease electric lock unlocking
OFF - no impulse
DIP 10
ON - Extra thrust when reached closing position to make sure that the
mechanical bolt is fixed into the ground
OFF no impulse
DIP 11
ON - black out function ENABLED (See chart 2)
OFF - black out function DISABLED
DIP 12
ON - close command after the transit through the photocell ENABLED
OFF - close command after the transit through the photocell DISABLED
DIP 13
ON - safety strip self-test ENABLED
OFF - safety strip self-test DISABLED
DIP 14
to select type of motor (see chart 1)
DIP 15
to select type of motor (see chart 1)
DIP 16
to select type of motor (see chart 1)
JP 17
OPEN JUMPER 1 motor (M1) - 1 leaf
CLOSE JUMPER 2 motors (M1 and M2) - 2 leaves
JP1 =>
Pay attention that the jumper is inserted!
JP2 =>
Pay attention that the jumper is inserted!
JP3 =>
Pay attention that the jumper is inserted!
TOrQUE Tr1 Electronic regulator for motor torque
Adjustment of motor torque is carried out using the TORQUE Trimmer which varies
the output voltage to the head/s of the motor/s (turn clockwise to increase torque).
This torque control is activated after 2 seconds form any manoeuvre begging,
whereas the motor is turned on at full power to guarantee the starting at the
manoeuvre begging.
PAY ATTENTION: If THE TOrQUE TrIMMEr sETTING Is CHANGED, IT Is
PrEfErABLE TO rEPEAT THE TIME PrOGrAMMING.
LOW sPEED Tr2 Electronic regulator for low speed on approach
Adjustment of low speed is carried out using the LOW SPEED Trimmer which
varies the output voltage to the head/s of the motor/s (turn clockwise to increase
speed). Adjustment is carried out to establish the correct speed at the completion
of opening and closing, depending on the structure of the gate, or if there is any
light friction that could compromise the correct working of the system. The low
speed is activated (DIP7 OFF) when the gate leaf is 0.50-0.60 meters away from
the complete close or open position.
ATTENTION: WHEN UsING HYDrAULIC OPErATOrs
When using the hydraulic operators the deceleration phase may not operate
correctly; in that case it is advisable to disable the feature of the deceleration
by putting DIP 7 in the Off mode.
LED WArNING
DL1 - programming activated (red)
DL2 - radio code programming (green) (only for CRX)
DL3 - gate opening M2 (green)
DL4 - gate closing M2 (red)
DL5 - gate opening M1 (green)
DL6 - gate closing M1 (red)
DL7 - photocell contact (NC) (red)
DL8 - safety strip contact (NC) (red)
fUsEs
F1 T315mA Accessories protection fuse
F2 5A Motor protection fuse
POINT C
- MOTOr rOTATION DIrECTION CHECK
1 - Unlock the operators with the Manual Release - swing open the leaves about
halfway and lock again the operators.
2 - Turn DIP1 to ON position The red LED DL1 starts blinking.
3 - Press the PROG button and hold it - When GREEN LEDS DL3 and DL5 are
on, the gate leaves are opening (with a phase shift of 2 seconds). Check the
leaves swinging and the opening mechanical stopper position (movement is
now performed in “man present” mode, open-close-open-etc.).
If any of the leaf closes instead of opening, release PROG button, turn off the
main power and reverse the two phase wires (V1/2 and W1/2) of the relevant
motor/s.
4 - Press the PROG button and hold it to CLOSE completely the gate. When RED
LEDS DL4 and DL6 are on, the gate leaves are closing (with a phase shift of 4
seconds). Check leaves swinging and the closing mechanical stopper position.
5 - After 3 seconds motor starting and for the next 10 seconds motor working, the
torque controls automatically activated. Set the motor torque by the TORQUE
Trimmer/s which varies the output voltage to the motor/s (turn clockwise to
increase the torque).
6 - After other 10 seconds motor working, the low speed controls automatically
activated (DIP7 ON). Set the motor low speed by the LOW SPEED Trimmer to
select the gate leaf low speed in approaching.
7 - Close completely the gate.
8 - Turn DIP1 to OFF position, LED DL1 turns off.
During Point C procedure, safety devices (photocells and safetystrip) are not
active and the remote control cannot operate.
(#) In Point D, Point E and Point F procedures, all the safety devices (photocells
and safety strip) will be active, so they must be properly installed and connected
to the control board. Any changing of the safety devices input state, will stop the
Point D, Point E or Point F procedure that must be repeated from the beginning.
POINT D
- PrOGrAMMING fOr 2 MOTOrs (#)
1 - The gate must be fully closed.
TABLE 1
TYPE OF MOTOR
CODE
DIP 14
DIP 15
DIP 16
1 KING 230/50
AA14001
OFF
OFF
OFF
KING L 230/50
AA14010
KING 220/60
AA14002
KING L 220/60
AA14011
KING ICE 230/50
AA14019
2 MAGIC IRR. 105°
AA10960
ON
OFF
OFF
MAGIC IRR. 180°
AA10965
MAGIC REV. 105°
AA10920
MAGIC REV. 180°
AA10930
DUKE 110°
AA10975
DUKE 180°
AA10985
PRATIC
AA18001
3 PRINCE REV
AA14045
OFF
ON
OFF
4 IDRO DUE 27/R
AA10843
ON
ON
OFF
IDRO DUE 27/1B
AA10844
IDRO DUE 27 SUPER/R
AA10809
IDRO DUE 27 SUPER/1B
AA10804
5 FLUID R DVI
AA10899
OFF
OFF
ON
FLUID R SVI
AA10901
FLUID 2B DVI
AA10897
FLUID 2B SVI
AA10898
IDRO 39/R
AA10871
IDRO 39/1B
AA10876
IDRO 39/2B
AA10881
6 KING FAST 230/50
AA14008
ON
OFF
ON
KING 120/60
AA14003
KING L 120/60
AA14012
7 R50
AA21580
OFF
ON
ON
8 IDRO C 27/1B
AA10884
ON
ON
ON
IDRO C 27/2B
AA10882
IDRO C 27/R
AA10883
