RF Venue 4 ZONE Instruction Manual Download Page 1

4ZONE 

4 Zone Antenna Combiner for Wireless Microphones

The 4ZONE is designed to combine multiple pairs of diversity antennas used for wireless microphone receivers. It provides 2 
x 4 antenna inputs to maximize coverage areas. It features RF input ON/OFF, input attenuation from 0 dB to -31 dB, DC 
power for in-line amplifiers or active antennas, and individual input signal ON/OFF control. 

Instruction Manual

Specifications 

Accessories 

Operating Controls

 

AC Power Cable x1

 

BNC to BNC coaxial Cable x2

Power switch

Antenna Selection key: Select the CH to be set, press and hold for 2 seconds to enter the settings mode.

Up / Down key: In the settings mode, press the up / down key to select the parameter.

Lock key: press and hold for 2 seconds to lock or unlock panel key function

3-digit display

Settings Selection Indicator

Status indicator: Indicates the current antenna status,

4ZONE Front Panel

2

7

3

5

4

Caution : To reduce the risk of fire or shock hazard, do not expose this appliance to heat or moisture. 
Warning : To prevent electric shock, do not remove the cover. Refer all servicing to qualified service personnel or distributors. 

Read this instruction manual before using.

Keep this instruction manual for future reference.

•Use in a well ventilated area. Do not block any ventilation openings.

•Do not use near heat sources.

•Do not use in humid or dusty environments.

•Turn power off immediately in the event of a spill or if the unit overheats.

• Carrier Frequency Range: 470~960MHz
• Full System Gain: 3dB(±3dB)
• Input/Output Impedance: 50 Ω
• A/B Antenna Input:4+4 
• OIP3: -35dBm(typ.) @ 2-tone

Pi=-15dBm/tone

• RF Input Attenuation: -31~0dB (Step:1dB)
• Input/Output Connectors: BNC(F):Input x8 / Output x2
• Functions: 

1. DC Power (for In-Line Amplifier) ON/OFF Control
2. RF Input Attenuation Control 
3. RF Input Signal ON/OFF Control

• In-Line Amplifier Power: 12V/200mA*8
• Power Supply: 100~240VAC; MAX 2A 50/60Hz
• Dimension(mm): 480mm(W)*45mm(H)*260mm(D)

1

2

3

5

4

6

7

a. Red: RF input enabled, In-Line Amplifier power on. 

b. Green: RF input enabled, In-Line Amplifier power off.

c. Off: The antenna input is disabled.

d. All 8 channels flashing at the same time: Power supply is abnormal. Please shut down immediately.

RF Attenuation

A1

A2

A3

A4

B1

B2

B3

B4

DC Power

Input ON/OFF

Lock

6

To enter the settings mode, press and hold the desired input channel’s Antenna Selection key 

 for 2 seconds until the input 

channel’s indicator light flashes. Use the Antenna Selection key to cycle through the 3 settings menus as indicated by the Settings 
Selection Indicator 

.  Use the Up / Down keys 

 to change the parameters in each settings mode. After setting your 

parameters in the third settings mode (RF Input), press the Antenna Selection key a final time to save and exit the settings.  For a 
step by step video, please visit rfvenue.com.    

Setting Parameters:

 RF input attenuation

Press the up / down key to adjust the input attenuation in 1dB increments.
0dB: No attenuation
Maximum attenuation level is - 31dB per input channel

 Antenna DC power

On (a12V DC / 200mA to RF input channels for active antennas or in-line amplifiers)
OFF

 RF Input ON/OFF

En: Input Enabled
dis: input disabled; signal isolation ~ 80 dBm

 To Return to Default Settings

1. Turn off the power
2. Press and hold the Lock Key 
3. Turn on the power while continuing to hold the lock key until the display show rSt

Operation

Notes

• This product is designed for combining receive antennas for wireless microphone receivers and is not recommended for use with transmitters.
• Use standard 50Ω coaxial cable.
•  An In-Line Amplifier may be used to compensate for losses associated with long runs of coaxial cable.  Enable DC power when using amplifiers.
• Adjust the RF input attenuation levels if signals exceed normal ranges of wireless microphone receivers. 
 

59010-531-01

1

4

RF Attenuation

DC Power

Input ON/OFF

-10

Attenuation of 10dB

DC Power

RF Input Enable

RF Attenuation

DC Power

Input ON/OFF

RF Attenuation

DC Power

Input ON/OFF

RF Attenuation

DC Power

Input ON/OFF

4ZONE

4 Zone Antenna Combiner

Reviews: