manualshive.com logo in svg

REWIRE SECURITY DB3, User Manual, Page: 99 / 122

Share
Download
REWIRE SECURITY DB3 User Manual Download Page 99

0.25  

0.85  

0.35  

Scenarios Enable 
(ID=1600)

  

Float  

 

9.6.4  Max Angular Velocity (ID=1604) 
  

It is max allowed cornering angle which can be reached while cornering without 
triggering harsh cornering event.  

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

0.1  

1.0  

-  

Scenarios Enable 
(ID=1600)

  

U16  

 

9.6.5  Max allowed Speed (ID=1605)  

It is max allowed speed which can be reached. If this value exceeded Over 
speeding event will occur.  

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

0  

260  

-  

Scenarios Enable 
(ID=1600)

  

U16  

 

9.6.6  Excessive Idling Detection (ID=1607)  

If ignition is ON and no movement, the event will be generated when TMO 
reached. This functionality is 1 – enabled, 0 – disabled (default).  

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

0  

255  

-  

Time to stationary 
(ID=1608) 

 

U8  

Summary of Contents for DB3



























































































































Reviews:

No comments