REWIRE SECURITY DB3 User Manual Download Page 98

Page: 98 / 122

9.5.6.6 GPRS Week Time (ID=1595)

Read GPRS Week Time (ID=1545)

9.6 Features Parameters

9.6.1 Scenarios Enable (ID=1600)

The device can operate in its scenario according to selected value: No Scenario
selected (value 0); Green Driving selected (value 1), Overspeeding selected
(value 2), Green Driving & Overspeeding selected (value 3).

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

9.6.2 Max Acceleration Force (ID=1602)

It is max allowed acceleration force which can be reached while accelerating
without triggering harsh acceleration event.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

0.25

0.85

0.25

Scenarios Enable
(ID=1600)

Float

9.6.3 Max Braking Force (ID=1603)

It is max allowed braking force which can be reached while braking without
triggering harsh braking event.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

Summary of Contents for DB3



























































































































Search results

Summary of Contents for DB3

Reviews:

REWIRE SECURITY DB3, User Manual, Page: 98 / 122

Search results

Summary of Contents for DB3

Reviews: