manualshive.com logo in svg

REWIRE SECURITY DB3, User Manual, Page: 94 / 122

Share
Download
REWIRE SECURITY DB3 User Manual Download Page 94

GPRS Week Time 
(ID=1575) 

 

  

9.5.4.5 Send Period (ID=1574)  

 

This parameter indicates frequency (time interval in seconds) of sending data 
to the server.   

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

0  

2592000  

-  

Min Saved Records 
(ID=1573) GPRS Week 
Time (ID=1575) 

 

U32  

  

9.5.4.6 GPRS Week Time (ID=1575)  

 

Read GPRS Week Time (ID=1545) 

 

 

 

9.5.5  Unknown Network GSM 

Operator Code “

Vehicle On STOP

” 

Parameters  

 

 

 

9.5.5.1 Min Period (ID=1580)  

 

This parameter indicates time interval in seconds in order to acquire new 
record. If the value is 0 it means no records by min period will be saved.  

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

0  

2592000  

-  

  

U32  

  

Summary of Contents for DB3



























































































































Reviews:

No comments