manualshive.com logo in svg

REWIRE SECURITY DB3, User Manual, Page: 83 / 122

Share
Download
REWIRE SECURITY DB3 User Manual Download Page 83

Target Main Server Port 
(1246) 

 

GPRS content activation 
(ID=1240) 

 

Main Server 

Domain (ID=1245)

  

 

9.4.8  Target Backup Server Port (ID=1248)  

 

Parameter defines AVL data destination backup server port number.   

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

Empty  

65535  

-  

GPRS content ac

t

ivation 

(ID=1240) 

 

Backup Server Domain 
(ID=1241) 

 

Target Main Server Port 
(1246) 

 

GPRS content activation

 

(ID=1240)

   

Main Server Domain 
(ID=1245)

  

U16  

 

9.4.9  Protocol (ID=1247)  

 

Parameter defines GPRS data transport protocol for main server. Module can 
use TCP or UDP transport protocol to send data to server. For TCP protocol 
value is 0, for UDP protocol value is 1.    

Minimum 
value 

 

Maximum 
value 

 

Recommended 

 

value 

 

Goes with (depends on) 
parameters 

 

Value 
type 

 

Summary of Contents for DB3



























































































































Reviews:

No comments