REWIRE SECURITY DB3 User Manual Download Page 74 | Manualshive

Page: 74 / 122

REWIRE SECURITY DB3 User Manual Download Page 74

flush

#,#,#,#,#,#,#

Initiates all data sending to specified target server

1.

# – IMEI

2.

# – APN

3.

# – LOGIN

4.

# – PASS

5.

# – IP

6.

# – PORT

7.

# – MODE (0 – TCP; 1 – UDP)

sn x [x=0;1]

Enable/disable static navigation

banlist

Banlist information

crashlog

Crash log information

delete_all_sms

Delete all read SMS

braminfo

BatRam info

getgnss

Current GNSS information

resetlimits

Resets data counters

ATTENTION!

In order to send these commands, they have to be converted to
a special format. How to convert to this format and for

additional information on how to send GPRS commands, please contact your
local sales representative.

8. Debug mode

DB3 Plug&Play is able to transmit its current state when connected to PC using
the USB cable. It is used to detect errors and provide information to possible
solutions when operating as unexpected.

After launching terminal choose baud rate 115200 and hardware control –
none. Select COM port which is assigned to “Virtual COM Port”. Click on ‘Start

«
...
72
73
74
75
76
...
»

Summary of Contents for DB3



























































































































Reviews:

No comments