
GENERAL DESCRIPTION
The Wolfspider Goggle System consists of an interchangeable protective lens that locks into
the goggle frame with an adjustable headband. Depending upon the model that you have
received, there may be additional lenses that all provide 100% UV protection. For example:
•
Clear for indoor and nocturnal use
•
Solar for daytime use to cut glare
•
High-Contrast for low-light conditions
The adjustable head strap keeps goggles secure during rigorous activity. Depending on the
model you have received, an anti-reflective sleeve, microfiber cleaning pouch/cloth (ideal
for cleaning your lenses) and rugged storage case may also be included.
OPTIONAL PRESCRIPTION (Rx) CARRIER
If you require corrective lenses, an optional Rx Carrier for prescriptions is available. You
can provide the Rx Carrier to your Optometrist who will insert your prescription lenses into
the Rx Carrier.
REMOVING THE LENS FROM THE FRAME:
Grasp the center of the top of the frame with your thumb and forefinger of one hand, and the center bottom
of the frame with the other hand. Pull the frame from the top and bottom, peeling it away from the lens.
While squeezing the goggle nosepiece together to release the lens from the nose, pull lens away
from goggle.
INSTALLING THE LENS INTO THE FRAME:
Working from the front of the goggles, first insert the right edge of the lens into the slot in the right edge of
the frame. Then repeat on the left side. Press the lens into the nosepiece area of the frame until it is locked
into place. Then firmly push the top of the frame. Be sure to fit the keyhole notches securely over the posts
so that the lens notch is not showing.
When the lens is completely inserted, ensure there are no gaps showing between the lens and the frame.
Clean lens (see below) to remove fingerprints and smudges.
REMOVING THE SLEEVE:
First remove the lens from the frame. Next, grasp the goggle frame with your thumb and forefinger. Peel
away the side clip from the top of the frame and remove the sleeve from the strap.
To fasten the side-clip:
Grasp the goggle frame with your thumb and forefinger. First, align the hole on the bottom of the frame
with the posts on the side clip and press into place. Then push the second post in the bottom into the
corresponding hole on the clip. Do the same with the holes on the top of the frame and side clip.
INSERTING THE OPTIONAL PRESCRIPTION (RX) CONNECTOR & CARRIER
To insert your Rx Carrier, first insert the Rx Connector into the frame by fitting the keyhole notches over
the posts at the nose bridge. Be sure that the soft bumper pad faces toward the lens, away from the face.
Insert the Rx Carrier into the Rx Connector by aligning the oval post at the center of the Rx Carrier with the
oval hole on the Rx Connector. Gently push the Rx Carrier down until it fits snugly into place.
CARE, CLEANING & MAINTENANCE
The lenses in your Wolfspider System include abrasion and fog resistant coatings. To extend the life of the lenses, clean and store your eyewear away from direct
sunlight and at room temperature when not in use. To clean and disinfect standard lenses, wash with lukewarm water and blot dry with a microfiber cloth.
To clean and disinfect the goggle frame and strap, remove the lens and hand wash the goggle frame in a mild soapy solution, rinse and air-dry.
INSTRUCTIONS
WEARING OVER HELMET STRAP ADJUSTMENT
To tighten the elastic head strap, move the slider
clips apart, towards your face, adjusting until the
system fits comfortably and snugly against your
face. To loosen, move the right and left slider clips
together.
CHANGING THE LENS
High-impact goggles require the lens to be held
very securely within the goggle frame for best
performance and for your protection. Do not be
afraid to apply force to the lens and put pressure
on the flexible frame when removing or inserting
the lens. Revision Goggles are built tough. They
can take it.
IMPORTANT
© 2013 REVISION MILITARY INC., WOLFSPIDER® AND REVISION® ARE TRADEMARKS OF REVISION MILITARY.
5-0330-0004 SEPT/2013
WOLFSPIDER
®
GOGGLE SYSTEM
USER INSTRUCTIONS