INSTALLING ASSEMBLIES FOR
TWO APPLIANCES
The appliance assembly kit can be used only for Vision electric
appliances, and their content varies based on the model and size
of the appliance in the assembly. After unpacking the kit, check it
against the packing slip for completeness.
SETTING UP AND INSTALLING THE
ASSEMBLIES FOR TWO APPLIANCES
•
Set the base (1) at the required location and use the height-
adjustable feet to even it out to horizontal position. (Use
a bubble level.)
•
Remove the left cover (11) of the appliance, which will be at the
bottom of the assembly. Then remove the composite strut (2)
supplied in the assembly kit. Slide the individual parts of the
strut behind the internal components, and insert and tighten it
underneath the screw of the left rear foot.
•
For 623/623 assemblies, it is necessary to remove the rear
ventilation cover (25). Screw the strut (2) to the base surface.
•
Put the left cover back on.
•
Place the appliance on the base such that the base’s pins (17) fall
into the holes in the appliance feet (18).
•
Temporarily remove the upper door hinge (9) and door (10).
•
Apply silicone sealant around the flap and chimney holes for
sealing against running water.
•
On the roof off the lower appliance, place the stiffening plate
with pegs (7).
•
Reinstall the door (10).
•
Adjust the door according to the door adjustment instructions.
For assembly 0623/0623:
•
Slip the adapter with the seal (27) on the chimney of the lower
appliance. Next attach the plastic joints in the order 45° and 90°.
For assembly 0611/0611, 0611/1011 including gas appliances:
•
Slip the joint with O-ring (4) on the chimney of the lower
appliance.
•
For a gas appliance, slip the seal (22) onto the screws of the
stiffening plate (7) and then screw on the external gas flue.
In addition, for both sets:
•
Place the second appliance on top of the first one so that the
pins on the stiffening plate (16) fall into the holes in the feet (19)
of the upper appliance.
•
Use the height-adjustable feet to even the appliance into an
horizontal position. (Use a bubble level.)
•
On assembly 623/623, slide the adapter (27) onto the upper
appliance’s drain. Install the sheet-metal base (28), insert the
aforementioned adapter, and screw it to the stiffening plate (7)
with just one screw.
•
Connect the outdoor chimney (5) using the connection hose
(12) and clamps (13) and fasten it to the internal ventilation
chimney (15).
•
Screw the side connection covers (3, 6, 8) to the holder of the
stiffening plate so that first you place the front cover (8), then
the right cover (7), and then the hole (20) including the seal (21)
in the left cover (3), thread the spray hose through and screw on
the cover.
•
Connect both appliances to the electrical grid and with the
drain joint (14) (29) into the drain according the installation
instructions.
Figure II.24 - Assembly of two devices 0623 and 0623
POSITION:
1 - pedestal under assembly, 2 - brace, 3 - left
connecting cover, 5 - external chimney with attachment, 6 -
right-hand connection cover, 7 - reinforcement sheet, 8 - front
connection cover, 9 - upper door hinges, 10 - door, 11 - left
cover of lower appliance, 16 - pins on reinforcement plate, 17 -
pins on pedestal, 18 - feet of bottom appliance, 19 - feet of upper
appliance, 20 - hole for shower hose, 21 - rubber bushing, 25 -
back cover with ventilation, 26 - plastic joints 45° and 90°, 27 -
adapter, 28 - sheet metal pedestal, 29 - plastic tube.