manualshive.com logo in svg

REPLIGEN XCell ATF Series, User Manual

Share
Download
REPLIGEN XCell ATF Series User Manual Download Page 63

 
XCell

TM

 ATF System with C410:V4B Controller   

 

 

 

 

 

 

 

User Guide 

 

 

 

59 

 
Figure 9:

 

Filtration Assembly Prepared for Autoclaving 

 

 
8.1.5

  Close all unprotected ports. 

8.1.6

  Depending on the size/configuration of the autoclave, the Filtration Assembly can be placed 

inside the autoclave either vertically or at an angle if necessary. Most autoclaves are not 
sufficiently tall for vertical placement.  

8.1.7

  Use caution during the procedure so not to damage attached parts or tubing. Avoid kinking 

or stressing attached tubing.  

8.2

 

Autoclave Cycle 

8.2.1 

The Xcell ATF systems have been designed to be sterilized using an autoclave.  

The XCell ATF System Filter Preparation and Autoclave Guide provides detailed 
guidance on the entire procedure including the recommended filter integrity test 
procedures and specifications.  The features of the recommended cycle are intended 
to ensure that the system will be effectively sterilized and that there is minimal 
thermal stress imposed on the hollow fiber cartridge that could lead to integrity 
failures.  

Summary of Contents for XCell ATF Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands