manualshive.com logo in svg

REPLIGEN XCell ATF Series, User Manual

Share
Download
REPLIGEN XCell ATF Series User Manual Download Page 60

 
XCell

TM

 ATF System with C410:V4B Controller   

 

 

 

 

 

 

 

User Guide 

 

 

 

56 

b4.

 

Press the HFM with “O” ring firmly i

nto the housing.  

 

Assure the “O” ring is inserted smoothly and uniformly. Lubricate with WFI to facilitate this 

process. 

b5.

 

 

Press until the HFM “O” ring groove is exposed at the other end

, the Drain nozzle 

end. 

b6.

 

Place 2

nd

 

“O” ring on the exposed end.

 

b7.

 

Press the HFM back into the Filter Housing until both “O” rings seal against the 

housing   ID. 

b8.

 

Assemble the system. 

 

1.3.2

 

I-Line HFM insertion: 

c1.

 

Stand the Filter Housing vertically, with harvest port up. 

c2.

 

Insert the HFM into the housing 

c3.

 

Insert one “O” ring into the groove formed between HFM and Filter Housing end

-

ferrule wall. 

c4.

 

Place the reducer onto the end, forcing the “O” ring into the groove.

 

c5.

 

Clamp the reducer to the housing, the compressed “O” ring is forced against the 

HFM. A seal is formed between the Housing, Reducer and HFM 

c6.

 

On the other end of the Filter Housing, P

lace the second “O” ring

 into the formed 

groove between HFM and Housing end-ferrule. 

c7.

 

Carefully place the Filter Housing onto the Diaphragm P

ump, forcing the “O” r

ing 

deeper into the groove. 

c8.

 

Clamp the Filter Housing to the Diaphragm Pump.  

c9.

 

Assemble the 

XCell™ ATF

 System.     

 

7.4

 

Screen Module replacement 

If the SM is being used, contact Repligen at

 

Customer Service at 

[email protected]

 for 

replacement instructions. 

 

7.5

 

Diaphragm replacement 

Replacement or placement of a diaphragm within the Diaphragm Pump is part of the Diaphragm 
Pump assembly process which differs slightly among the 

XCell™ ATF 

4 System, 

XCell™ ATF 

6 System, 

XCell™ ATF 

8 System and 

XCell™ ATF 

10 System. 

 

Diaphragm Replacement Procedure for the 

XCell™ ATF 

4 System, 

XCell™ ATF 

6 System and 

XCell™ 

ATF 8 System 

 

d1.  Place cleaned Diaphragm Pump hemispheres, diaphragm and pump clamp on a table top 
d2.  Place the PL pump hemisphere (hemisphere with a nozzle on the side) with the large 

opening in the upward position. 

Summary of Contents for XCell ATF Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands