manualshive.com logo in svg

REPLIGEN XCell ATF Series, User Manual

Share
Download
REPLIGEN XCell ATF Series User Manual Download Page 58

 
XCell

TM

 ATF System with C410:V4B Controller   

 

 

 

 

 

 

 

User Guide 

 

 

 

54 

7.0

 

XCell™ ATF 

Hollow Fiber Module and Diaphragm Replacement 

 
The following is a guideline for replacing a Hollow Fiber Module (HFM) or the diaphragm within the 
Diaphragm Pump. Since the procedures for replacing these parts are similar, a generalized description is 
provided. Where necessary, more specific references and descriptions will be provided. 

 

Example 2 

Replacing a HFM in Filtration Assembly connected to a pressure rated vessel: 

 

Prerequisites:  Steam is available and the HFM has to be replaced in mid run in a sterile manner. Refer to 
Figure 1.  

 

7.1

 

Separating the Filtration Assembly from the bioreactor 

 

7.1.1 

STOP the C410v4B controller. 

7.1.2

 Stop the filtrate / harvest pump. 

7.1.3

 Disconnect Diaphragm Pump pneumatic line from the pump air inlet filter. 

7.1.4

 Close or disconnect compressed air and vacuum services from the P-BOX. 

7.1.5

 Disconnect any sensors from the Filtration Assembly to P-BOX  

7.1.6

 If necessary, remove the P-BOX from the proximity of the Filtration Assembly. 

7.1.7 

Close and disconnect the filtrate line.  

7.1.8

 

Disconnect the Filtration Assembly from the vessel as follows: 

a1.  Securely close both bivalves connecting the Filtration Assembly to the vessel. 
a2.  Drain liquid from the connection. Optionally, purge the connection with water, steam or 

some other medium. 

a3.  Disconnect the Filtration Assembly from vessel between the two bivalves. 
a4.  Remove the Filtration Assembly to an appropriate work area, i.e., a sink. 

 

7.2

 

 HFM removal 

 

7.2.1 

Drain the system into an appropriately sized drain or waste vessel. 

7.2.2

 Remove all sensors from the Filter Housing 

7.2.3 

Remove air inlet filter connected to the Diaphragm Pump and any other connections 
to the  

XCell™ ATF

 System 

     

7.2.4 

Open the clamp connecting the Filter Housing to the Diaphragm Pump and separate 

7.2.5

 Open the clamp connecting the Reducer to the Filter Housing and separate 

7.2.6 

The HFM may then be removed from the Filter Housing by firmly pressing it from one 
end 

7.2.7 

Remove the exposed “O” ring at the exposed end of the HFM

 

7.2.8 

Press the HFM in the opposite direction to remove the HFM 

1.2.9

 

Prepare Filter Housing for cleaning and reuse or for cleaning and setting aside 

 

 

Summary of Contents for XCell ATF Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands