manualshive.com logo in svg

REPLIGEN XCell ATF Series, User Manual

Share
Download
REPLIGEN XCell ATF Series User Manual Download Page 24

 
XCell

TM

 ATF System with C410:V4B Controller   

 

 

 

 

 

 

 

User Guide 

 

 

 

20 

 

5.5

 

Power Box (Power Separation) Components 

s.     Interconnected Cable Plug (power) 
t.     Mains power plug, 120/220 vac 60/50 hz 
u.    Illunminated On/Off switch 

 

Figure 5d.   Power Box Connections 

 

                              

†

Note: The electric plug design may vary depending on geography 

 
 
 

5.6

 

Primary Pneumatic Services 

Air inlet (q) - 

Located on the P-Box and provides an inlet to house compressed air source.  

Recommended minimum air pressure requirement is ~50psi / 3.4bar. 

 

Somewhat higher inlet 

pressures may be required, as needed, to generate higher flow rates or to drive pneumatic 
instruments.    

Do not exceed 90 psi / 6.1 bar on the Air inlet 

Exhaust/ vacuum line (r) - 

Located on the P-Box.

 

Leaving the Exhaust

 

outlet open to the 

atmosphere or connected to a vacuum line, will depend on the type of process vessel used. 
For a vessel that cannot be pressurized (e.g., some stainless steel vessels, glass vessels, SUB, 
etc.), the line is connected to a vacuum source. For a vessel that is pressure rated, one may 
use vessel pressure to drive the Exhaust cycle, particularly at low 

XCell™ ATF

 System flow 

rates; but in case where vessel pressure is limited, or at high 

XCell™ ATF

 System flow settings, 

a vacuum source supplement may be required. 
 

Note: In addition to vessel pressure, the hydrostatic pressure generated by the height difference between 
vessel liquid level and pump level may assist or hamper the exhaust flow

 

 

Summary of Contents for XCell ATF Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands