background image

R12UZ0012EG0110 Rev. 1.10 

 

Page 3 of 34 

Apr 03, 2017 

 

 

Disclaimer 

 

By using this Solution Kit, the user accepts the following terms: 

 

The  Solution Kit  is not guaranteed to be error free, and the entire risk as to the results and performance of the 
Solution Kit is assumed by the User. The Solution Kit is provided by Renesas on an “as is” basis without warranty 
of any kind whether express or implied, including but not limited to the implied warranties of satisfactory quality, 
fitness for a particular purpose, title and non-infringement of intellectual property rights with regard to the Solution 
Kit. Renesas expressly disclaims all such warranties. Renesas or its affiliates shall in no event be liable for any loss 
of profit, loss of data, loss of contract, loss of business, damage to reputation or goodwill, any economic loss, any 
reprogramming or recall costs (whether the foregoing losses are direct or indirect) nor shall Renesas or its affiliates 
be liable for any other direct or indirect special, incidental or consequential damages arising out of or in relation to 
the use of this Solution Kit, even if Renesas or its affiliates have been advised of the possibility of such damages.  

 

Precautions 

 

The following precautions should be observed when operating any Solution Kit product: 

 

 

This  Solution Kit  is only intended for use in a laboratory environment under ambient temperature and humidity 
conditions. A safe separation distance should be used between this and any sensitive equipment. Its use outside the 
laboratory, classroom, study area or similar such area invalidates conformity with the protection requirements of the 
Electromagnetic Compatibility Directive and could lead to prosecution.  

 

The product generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment causes harmful interference to radio or television reception, which can be determined by turning the 
equipment off or on, you are encouraged to try to correct the interference by one or more of the following measures;  

 

  ensure attached cables do not lie across the equipment  

  reorient the receiving antenna  

  increase the distance between the equipment and the receiver  

  connect the equipment into an outlet on a circuit different from that which the receiver is connected  

  power down the equipment when not in use  

  consult the dealer or an experienced radio/TV technician for help NOTE: It is recommended that wherever 

possible shielded interface cables are used.  

 

The product is potentially susceptible to certain EMC phenomena. To mitigate against them it is recommended that the 
following measures be undertaken;  

 

  The user is advised that mobile phones should not be used within 10m of the product when in use.  

  The user is advised to take ESD precautions when handling the equipment.  

 

The  Solution Kit  does not represent an ideal reference design for an end product and does not fulfil the regulatory 
standards for an end product. 

Summary of Contents for RX231



































Reviews: