manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 1613 of 1823

Jul 31, 2019

RX23W Group

44. 12-Bit A/D Converter (S12ADE)

44.5

Event Link Function

44.5.1

Event Output to the ELC

The ELC uses the S12ADI0 interrupt request signal as an event signal (S12ADELC), enabling link operation for the 
preset module. An event signal is generated under the conditions set by the event link control bits 
(ADELCCR.ELCC[1:0] bits).
The event signal can be output regardless of the setting of the corresponding interrupt request enable bit.
The 12-bit A/D converter outputs the A/D conversion end event (S12ADELC), window function compare match event 
(S12ADWMELC), and mismatch event (S12ADWUMELC).
The scan end event (S12ADELC) is output to the ELC at the same time as the interrupt output (S12ADI0) regardless of 
the ADCSR.ADIE setting.
The compare match/mismatch event (S12ADWMELC/S12ADWUMELC) is output to the ELC with a delay of one 
PCLK cycle from the interrupt output (S12ADI0) regardless of the ADCSR.ADIE setting.
When using compare match/mismatch events (S12ADWMELC/S12ADWUMELC) to the ELC, specify single scan 
mode.

44.5.2

12-Bit A/D Converter Operation by Event from the ELC

The 12-bit A/D converter can be started by the predetermined event by setting ELSRn of the ELC.

44.5.3

Note on 12-Bit A/D Converter When an Event Is Input from the ELC

If an event occurs during A/D conversion, the event is disabled.

44.6

Selecting Reference Voltage

For the A/D converter, the high-potential reference voltage can be selected from VREFH0 and AVCC0, and the low-
potential reference voltage can be selected from VREFL0 and AVSS0, respectively. Set these before starting A/D 
conversion. For details of this setting, see 

section 44.2.30, A/D High-Potential/Low-Potential Reference Voltage 

Control Register (ADHVREFCNT)

.

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
SUNRICH TECHNOLOGY C-330 User Manual preview
C-330
Brand: SUNRICH TECHNOLOGY Pages: 5
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Brand: MC Pages: 21
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Brand: Delta Electronics Pages: 1
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Brand: Pressalit Care Pages: 31
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
ZALMAN Fatal1ty FS-V7 User Manual preview
Fatal1ty FS-V7
Brand: ZALMAN Pages: 9
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
National Instruments PXI Terminal Block NI TB-2709 Installation Manual preview
PXI Terminal Block NI TB-2709
Brand: National Instruments Pages: 12
Sony Ericsson GC83 Specification preview
GC83
Brand: Sony Ericsson Pages: 2
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Brand: IBM Pages: 74
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Brand: Barracuda Pages: 8
Infoblox ND-2200 Installation Manual preview
ND-2200
Brand: Infoblox Pages: 44
National Instruments USB device 622x User Manual preview
USB device 622x
Brand: National Instruments Pages: 23
Hameg HM6050-2K Manual preview
HM6050-2K
Brand: Hameg Pages: 46
Stepper Motor Canada DB25-1R5AM Manual preview
DB25-1R5AM
Brand: Stepper Motor Canada Pages: 7

Brands by name

Popular brands

Load more brands