Renesas RTE7702500EAB00000J User Manual Download

Page: 3 / 63

Preface

The emulation adapter is an emulation board which is designed for use with RH850 family MCUs from

Renesas Electronics Corporation.

All components that come with the emulation adapter are listed under “1.1 Package Components”. If

you have any questions about the emulation adapter, contact your local distributor.

This user’s manual is mainly to describe the specifications of the emulation adapter. For the

specifications of the exchange adapters, refer to appendix A, Specifications of the Exchange Adapters,

in this document.

For information on emulator debuggers and related products, please see the user’s manuals, additional

documents for user’s manuals, and application notes provided for the individual products. When you

use an emulator from another company for debugging, be sure to read the user’s manual for the given

emulator.

Related Documents

Name of Document

Document No.

IE850A Emulator RTE0T0850AKCT00000J
User’s Manual

R20UT4461E

E2 Emulator RTE0T00020KCE00000R
User’s Manual

R20UT3538E

E2 Emulator, IE850A Emulator Additional Document for User’s Manual
(Notes on Connection of RH850/U2B)

R20UT5052E

Note: The contents of the related documents listed above may be changed without prior notice. Be

sure to use the latest versions of the documents, which can be downloaded from “Software and

Tools” on the Renesas Web page.

https://www.renesas.com/

Summary of Contents for RTE7702500EAB00000J
































































Search results

Summary of Contents for RTE7702500EAB00000J

Reviews:

Related manuals for RTE7702500EAB00000J

Brands by name

Popular brands

Renesas RTE7702500EAB00000J, User Manual

Search results

Summary of Contents for RTE7702500EAB00000J

Reviews:

Related manuals for RTE7702500EAB00000J

Brands by name

Popular brands