Renesas H8/3937 Series User Manual Download Page 14 | Manualshive

Page: 14 / 21

background image

2.3

Recommended Dimensions for User System Mount Pad

Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with
an IC socket for an TFP-100G package (NQPACK100SE: manufactured by Tokyo Eletech
Corporation). Note that the dimensions in figure 6 are somewhat different from those of the actual
chip's mount pad.

Figure 6 Recommended Dimensions for Mount Pad

10

«
...
12
13
14
15
16
...
»

Summary of Contents for H8/3937 Series






















Reviews:

No comments

Related manuals for H8/3937 Series

Brand: Garland Pages: 6

Brand: Tripp Lite Pages: 20

Brand: XNET Pages: 17

Brand: Cypress Semiconductor Pages: 33

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: IBM Pages: 78

Network Video Recorder

Brand: IC Realtime Pages: 118

Mobile Network Video Recorder

Brand: IC Realtime Pages: 158

Brand: Dell Pages: 37

Brand: D-Link Pages: 32

Brand: D-Link Pages: 27

DSN-4200 Series

Brand: D-Link Pages: 5

Brand: D-Link Pages: 8

Brand: D-Link Pages: 9

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 5

DSN-4100 Series

Brand: D-Link Pages: 5

Brand: D-Link Pages: 4

Brand: D-Link Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands