Renesas CE2000-H8S Series User Manual Download Page 23

Page: 23 / 96

Section 2. Setup

2.1 Express Setup Steps

•

Unpack and verify parts against the packing list.

•

Power up PC.

•

Install HEW by running setup file.

•

Power up the CE2000-H8S/2238 emulator.

•

Connect USB cable from PC to the emulator within 10 seconds. Otherwise, the CE2000-H8S/2238
emulator will go into Self Test mode.

•

Run HEW.

USB Interface

Power Supply

Compact Emulator

Figure 2-1

Basic Setup of CE2000-H8S/2238 Emulator

The following topics detail the essential steps before proper emulation can be started.

POWER Status LED
-RED: Power On
-ORANGE: Self Test
-ORANGE: PC Detection
-BLINK: Self Test Cycle ended

PC USB Connector

User Connector

PWR RUN

PC I/F

Power Supply Input

RUN Status LED
- RED: Self Test Failed
- GREEN: Run

Figure 2-2

Compact Emulator

www.DataSheet4U.com

Summary of Contents for CE2000-H8S Series

































































































Search results

Summary of Contents for CE2000-H8S Series

Reviews:

Related manuals for CE2000-H8S Series

Brands by name

Popular brands

Renesas CE2000-H8S Series, User Manual

Search results

Summary of Contents for CE2000-H8S Series

Reviews:

Related manuals for CE2000-H8S Series

Brands by name

Popular brands