in71TVI3N2D Series
Indoor Outdoor Bullet Camera
Quick Start Guide
Before operating this product, please read this quick-start guide to ensure proper use.
Please store these instructions a safe place for future reference.
FEATURES
•
IP68 Die Cast Aluminium Housing
•
Varifocal lens
•
High Resolution TVI (1080) Analog
(1000TVL)I
•
0 Lux IR on, 0.01 Lux
•
Wide Dynamic Range
•
Wire Management Mount
•
Sun Shield
•
HLM, BLC, DEFOG
•
Sens Up
•
On Screen Menu
•
3 Axis gimbal
•
12VDC/24VAC Powered
PRECAUTIONS
1. Before installing and operating the unit, please read this manual carefully.
2. Precision components are contained in this camera, please avoid violent vibrations during
installation and maintenance. Do not connect the power until you have completed the
installation.
3. Please obey all local electrical wiring regulations when using this unit.
4. Do not use abrasive or corrosive materials for cleaning. Use only a soft cloth for cleaning.
5. To prevent damage to the lens or sensor, do not point the camera directly into the sun
or very strong light sources.
6. Do not use the camera outside it’s working temperature (-10°C~ 50°C / 14°F ~122°F) or
humidity (<90%) ranges.
7. Ensure that the power supply meets the current requirements of the camera and that
the supply voltage is inside the tolerances of the camera: 12vdc or 24VAC ±10%
8. Ensure that the fixings used are adequate to support the load of camera.
9. In case of camera failure, do not attempt to dismantle or service the camera yourself.
Please refer to qualified service personnel for repair of the camera.
CONNECTIONS
1. Analog Video (Yellow) BNC Connector.
2. TVI Video (Black) BNC Connector
3. Power Input connector. This is a 2 pin non-removable terminal screw connector.
Observe polarity of 12VDC connections. 24VAC power is not polarity sensitive.
Refer to the diagrams below for clarification.
4. Thumb screw to attached Sun Shield
5. Sun Shield
6. Service Port for Analog Video
7. Focus Screw (Far:Near) Zoom Screw (Wide:Telephoto)
8. Service Cable
+ (Pos)
- (Neg)
When the OSD menu is launched, you are
presented with the adjacent opening screen.
A menu option followed by a
indicates the
presence of a sub-menu. Options set to OFF will
not show a
until set to ON
Use RETURN
to return to the previous menu.
EXPOSURE
menu:
• SENS-UP -
Select Off to 8x to enhance low
light performance. Slows frame rate and
increases low light sensitivity. When on
shutter cannot be selected
• BRIGHTNESS -
Sets the level of the overall
brightness
• SHUTTER
- Auto, Manual selection,
1/30~1/60K. Set this on to reduce the
exposure time of each image. This can be used to reduce blur in images with fast
changing content.
• AGC- Level Control -
Used to adjust overall gain
WHITE BALANCE
- AUTO, AUTO-EXT ,
PRESET, MANUAL
• AWB
-AUTO (default) The camera
automatically samples the image for
optimum white balance
• AUTO EXT
- The camera automatically
samples the image for optimum white
balance in an exterior environment.
• PRESET -
Allows the white balance to
be set automatically and locked.
This option is normally used when no
white reference is present in the image. To set the white balance, hold a white
object in front of the camera, with light from the source falling on it and press
the joystick to set and lock the white balance
MANUAL
- This option allows a selection of color temperature, Red and
Blue gain to be manually set in the image. Note, using this option requires care
to ensure all cameras on one system have the same color response.
SHARPNESS
- Level Control
DEFOG
- Used to help improve the
captured image in poor weather
conditions such as smog, fog, or smoke.
It automatically controls contrast ratio
by spatially analysing the histogram
characteristics
D-ZOOM -
0~127 Steps
Rev 0.1
MAIN MENU
EXPOSURE
WHITE BALANCE
AUTO
IMAGE.
BACKLIGHT
OFF
DAY&NIGHT
DNR
MIDDLE
MOTION
OFF
SERIAL
SPECIAL
SYSTEM
EXIT
EXPOSURE
SENS-UP
OFF
BRIGHNESS
LENS
MANUAL
AE MODE
NORMAL
SHUTTER
AUTO
AGC
DOUT SCALE COMP
RETURN
EXPOSURE MENU
IMAGE MENU
OSD MAIN MENU
LENS MENU
To set lens to correct field of view and focus remove the access plug on the bottom of the
camera. See image below. First plug your service cable into the service port ⑥ then into
your monitor. The field of view may then be adjusted by turning the zoom lever, ⑦, and
moving until the required field of view is obtained. Next turn the focus lever ⑦ and adjust
to obtain optimum focus. When complete screw the access port onto camera to maintian
water seal.
MOUNTING
1. Mark and drill the three mounting holes for the base. Choose an appropriate drill bit for the
surface you are drilling in to and ensure that the diameter is correct for the fixings being
used. Mark and cut/drill a central 20mm (¾”) diameter hole for the cable and connectors.
2. Use appropriate screws and wall plugs for the mounting surface in use.
3. Ensure that the fixings can adequately bear the weight of the camera.
4. Make the video and power connections and commission the camera.
LENS AND POSITIONING
The bullet camera has an integral varifocal lens, a OSD button and Service port (adjusted from
the access port on bottom of camera) along with a 3-axis mount which can be manipulated to
position the camera.
To position the camera to give the required image content, gently loosen the hex screws located
on the main mount to adjust fro pan, tilt , azimuth , gently turn to reach desired position then
retighten.
MAIN MENU
EXPOSURE
WHITE BALANCE
AUTO
IMAGE.
BACKLIGHT
OFF
DAY&NIGHT
DNR
MIDDLE
MOTION
OFF
SERIAL
SPECIAL
SYSTEM
EXIT
IMAGE MENU
SHARPNESS
6
DEFOG
OFF
D-ZOOM.
0
MIRROR
OFF
FLIP
OFF
FREEZE
OFF
PRIVACY
OFF
SHADING
OFF
COLOR GAIN
ACE
OFF
RETURN