background image

1

Back Bar & Beer Dispenser

RXBB-2472, RXBB-2472G 

RXBB-2448G, RXBB-2448G

PLEASE READ THE MANUAL THOROUGHLY PRIOR TO  

EQUIPMENT SET-UP, OPERATION AND MAINTENANCE.

NOTICE:

 Use this appliance for its intended purpose as described in this User Manual.

GENERAL INSTRUCTIONS

•  When the cooler is installed or used, all the packaging (including carton and plastic wrap) should be removed.
•  Keep the cooler stable to avoid vibration and noise.
•  The cooler should be installed in a place with good ventilation and a space of at least 4" should be allowed 

between the surrounding walls and the cabinet wall for air circulation.

•  Unit should be placed far from any heating source to avoid decrease of refrigeration efficiency.
•  Install the cooler in a dry place to prevent rust from forming on the compartment body, which may affect the 

electrical insulation.

CAUTION

•  The cooler must be grounded correctly, never to a heating pipe or water pipe. In case of damage to electrical 

cord and plug, please contact after-sale service — never do it yourself.

•  When unplugging unit, please grasp by the plug, not by the cord.
•  If the voltage is unstable, please use a suitable automatic voltage regulator.
•  If the power cuts off, you should wait for at least 5 minutes before turning on the unit again to avoid damage to 

the compressor.

•  Never store any flammable, explosive or corrosive liquid or gas in or near the cooler.

SAFETY

When using electrical appliances, basic safety precautions should be followed:
•  This unit must be properly installed and located in accordance with the installation instructions prior to use.
•  Do not allow children to climb, stand on or hang from the shelves in the cooler. This could damage the unit and 

cause serious injuries.

•  Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.
•  Unplug the unit from the electrical outlet before cleaning or making repairs.
•  Setting the temperature controls to the 0 (zero) position does not remove power to the light circuit, perimeter 

heaters or evaporator fans.

NOTE:

 It is strongly recommended that any servicing be performed by an certified technician.

For complete specifications on all Reliant products, please visit 

www.paragondirect.ca

 Commercial Refrigerator and Freezer

USER’S MANUAL

 Reliant_Back Bar_User Manual_Jan19

Summary of Contents for RXBB-2472









Reviews: