background image

MWS_55_e.indb Page 74

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

geändert am 04.12.2020 von  DO

REINHARDT 

System- und Messelectronic GmbH

Fax: 08196/7005 and 1414 email: 

[email protected]

  Web: 

http://www.reinhardt-wetterstationen.de

to table of contents

4.5 Wireless LAN (WLAN) built-in

Another interface option is the built-in WLAN interface.

This enables the weather station to transmit data via an IP address and 2 separate channels.

One channel offers full access to the station, the second limited access (read only).

The default is port 10001 for full access and port 10002 for limited access.

 

4.5.1 Settings for WLAN Option via WEB-Interface

If you did not specify a IP address when ordering your weather station with internal WLAN op-

tion, the  IP address is set to "

192.168.240.93/24"

, SSID is 

"WETTER"

 and security is 

"none"

(see XML-file 

xPico_set_#192_168_240_93.txt on stick)

This IP address takes you to the WEB interface of the WLAN module xPico-Wi-Fi, where you can 

perform all necessary settings.

Further information can be found in the two manuals for the xPico WLAN module 

(

xPico-Wi-Fi_UG.pdf

  and 

xPico_IG.pdf

). 

4.5.2 WEB-Interface of xPico WLAN-module

For accessing the WEB interface of the xPico WLAN 

module insert the module's address (in our case 

192.168.249.93) into a WEB browser. 

A password request will appear: 

The default user is 

admin

the default password is 

PASSWORD

After clicking onto OK, the WEB interface will open: 

Here you can perform all settings you'll need. 

Summary of Contents for MWS 10














































































































































Reviews: